How to Replace a Bathtub Yourself: Removing and also Replacing.
How to Replace a Bathtub Yourself: Removing and also Replacing.
Blog Article
In this article down the page you'll find some amazing help and advice around Tools You Need to Install a New Bathtub .
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately challenging project. If the old tub is easily easily accessible, the job can relocate speedily; if you need to open a wall to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to leave the old tub as well as set in the new one. Ensure you have qualified yourself for the task as well as fit trying it. Instead of employing a specialist to take over a halfway-completed job, it is better to consider using one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently bought a brand-new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices as well as product list need to make up the following:
Preparing for the Installation
First of all, the sustaining framework provided with the bathroom must be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps unit to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath must now prepare to be suited its last setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is separate the water supply. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the restricted accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the staying water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of both wooden boards under its feet, put the tub in the called for position. The wood boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little factors.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by inspecting the level and adjusting the feet on the tub up until the level reviews degree.
To mount faucets, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipe by making a compression join; then do the same for the other faucet.
Turn on the water and also check all joints and brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as also inspect the overflow outlet as well as the regular electrical outlet for leakages.
Finally, fix the bath paneling as defined in the supplier's instruction manual. Tiling and also securing around the bath tub must wait until the tub has actually been utilized a minimum of when as this will settle it right into its last setting.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making sure that the washing machines remain in area between the tap and the sink. Safeguard the faucet in place with the manufacturer provided backnut. Once the tap is firmly in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The former type needs to be linked to the tap ends first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to split a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, causing difficulties with dampness and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your components and also fittings. They are offered in tubes and cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill up the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealer can crack relatively very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that article on Tools You Need to Install a New Bathtub through an acquaintance on a different website. Are you aware of somebody else who is enthusiastic about the topic? Please feel free to promote it. I value reading our article about A Step-by-Step Guide to Installing a Bathtub.
View Report this page